Aplex-technology APC-3519 Manual de usuario

1 APC-3X19 User Manual Release Date Revision Apr 2014

10 1.3 Brief Description of APC-3X19 APC-3x19 is a fanless and high-performance panel-mount industrial panel PC with 15”/17/19” TFT LCD. I

11 1.4 Installation of HDD Step 1 There are 2 screws to deal with when enclosing or removing the HDD bracket. Step 2 There is 1 screw

12 Step 4 Tighten four screws as shown in the picture. F Screw M3*5L 120° Step 5 Push into the HDD bracket as shown in the picture Step 6 That

13 1.5 Installation of Riser Card Step 1 There are 2 screws to deal with when enclosing or removing the bracket. Step 2 Remove the cover

14 Step 4 Put the riser card in. Put the riser card in. Put the riser card in.

15 Step 5 Tighten two screws.

16 Chapter 2_____ __Hardware Installation 2.1 Mainboard Specifications Introduction ASB-M8771 is a Mini-ITX industrial motherboard developed

17 Specifications Board Size 170mm x 170mm CPU Support Support Socket G2, 2nd/3rd Gen Intel Core i3/i5/i7 Processors Chipset Intel HM77 (ASB-M8771H)

18 Digital I/O 8-bit digital I/O by Pin header by MIO2 4-bit digital Input 4-bit digital Output Battery Support CR2477 Li battery by 2-pin header Sup

19 Power Consumption 12V/3.80A (Intel i5-2430M 2.4GHz Processor with 4GB DDR3) 19V/2.0A (Intel i5-2540 2.6GHz Processor with 8GB DDR3) 19V/2.2A(Intel

2 Warning!____________________________ This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accor

20 Figure 2.3: Jumpers and Connectors Location- Bottom

21 1. RTC1/SRTC1: (2.0mm Pitch 1X2 Pin Header)CMOS clear jumper, CMOS clear operation will permanently reset old BIOS settings to factory defaults

22 5. DCIN: (5.08mm Pitch 1x3 Pin Connector),DC9V ~ DC32V System power input connector。 Pin# Power Input Pin1 DC+9V~32V Pin2 Ground Pin3 PG 6.

23 Pin1 DC+12V Pin2 Ground Pin3 Ground Pin4 DC+5V 9. U1: (Socket G2), installing the 2nd GEN intel Core i3/i5/i7CPU Socket. 10. CPU_FAN1/SYS_FA

24 Signal Name Pin# Pin# Signal Name VDD5 2 1 VDD5 Ground 4 3 Ground VDD33 6 5 VDD33 LB_D0_N 8 7 LA_D0_N LB_D0_P 10 9 LA_D0_P Ground 12 11 Ground L

25 15. HDMI1: (HDMI 19P Connector), High Definition Multimedia Interface connector. 16. DVI-I: (DVI-I Connector), Digital Visual Interface-Inte

26 20. COM1: (Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a direct connection to serial devices. RS232 (Default

27 21. JP2: (2.0mm Pitch 2x3 Pin Header),COM2 jumper setting, pin 1~6 are used to select signal out of pin 9 of COM2 port. JP2 Pin# Function Close

28 Close 1-2 COM6 Pin9 RI (Ring Indicator) (default) Close 3-4 COM6 Pin9=+5V (option) Close 5-6 COM6 Pin9=+12V (option) 25. COM6: (2.0mm Pitch 2

29 or amplifier, MIC is the port for microphone input audio. 28. AUDIO1: (2.0mm Pitch 2X6 Pin Header), Front Audio, An onboard Realtek ALC662 c

3 Packing List Accessories (as ticked) included in this package are: □ Power Connector □ Driver & manual CD disc □ Other.__________________

30 MODEL PC1E16X / PCIE1X ASB-M8771T Top ASB-M8771B Bottom 35. M-PCIE1: (Socket 52Pin),mini PCIe socket, it is located at the top, it supports min

31 39. MIO2: (DF13-40P Connector),Front panel connector. Function Signal Name Pin# Pin# Signal Name Function P_LED+ PWR-LED 2 1 HDD_LED H_LED+ P_L

32 Pin11~Pin18: GPIO IN/GPIO OUT, General-purpose input/output port, it provides a group of self-programming interfaces to customers for flexibl

33 42. SATA1/SATA2/SATA3/SATA4: (SATA 7P), SATA Connectors, Four SATA connectors are provided,SATA3 and SATA4 transfer speed up to 3.0Gb/s, SATA1 a

34 50. TB-525E161: TB-525E161 connect to ASB-M8771T PCIE_16X connector, PCIE_16X is located at the top,It provides one PCIE X16 slot. 51. TB-525

35 Chapter 3 BIOS Setup 3.1 Operations after POST Screen After CMOS discharge or BIOS flashing operation,.Press [

36 Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit System Language [Englis

37 3.4 Advanced Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit

38 PERR# Generation: SERR# Generation: [Disabled] [Enabled] [Disabled] [Enabled] [Disabled] [Enabled] PCI Express Device Settings： 3.4.2 ACP

39 Hyper-threaading [Enabled] [Disabled] Active Processor Cores [All] [1] Limit CPUID Maximum: [Disabled] [Enabled] Execute Disable Bit:

4 Table of Contents__________ Warning!…………………………………………………………………….……..….2 Disclaimer………………………………………………………….…………………2 Packing List.

40 IDE legacy / Native Mode Selection [Native] [Legacy] Serial ATA Port 0 Empty Software Preserve Unknown Serial ATA Port 1 Empty Software Pr

41 1 keyboard, 2 Hubs Legacy USB Support: EHCI Hand-off: Port 60/64 Emulation [Enabled] [Disabled] [Disabled] [Enabled] [Enabled] [Disabled]

42 +12V : +12.160 V +3.3V : +3.296 V +1.5V : +1.520 V AVCC : +5.158 V 3.4.13 Platform Misc Configuration 3.4.14 Intel(R) Smart

43 3.5 Chipset Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit

44 GTT Size Aperture Size DVMT Pre-allocated [Enabled] [2MB] [1MB] [256MB] [128MB] [512MB] [64MB] [32MB] [96MB] [128MB] [160MB] [192MB

45 [800 X 600 24bit 1ch] [1024 X 768 18bit 1ch] [1024 X 768 24bit 1ch] [1280 X 800 18bit 1ch] [1366 X 768 18bit 1ch] [1440 X 900 24bit 2ch] [1600 X 9

46 PEG0 [Not Present] PEG0 – Gen X [Auto] [Gen1] [Gen2] [Gen3] PEG ASPM [Auto] [Disabled] [Auto] [ASPM LOs] [ASPM L1] [ASPM LOsL1] De-emphasis

47 Wark on LAN Board Capability SLP_S4 Assertion Width Restore AC Power Loss Set NAND Management Override [Enabled] [Enabled] [Disabled]

48 3.6 Boot Settings Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc. Main Advanced Chipset Boot Security Save & Exit Boot

49 Option ROM Messages Interrupt 19 Capture [Force BIOS] [Keep Current] [Immediate] [Postponed] Boot Option Priorities ►CSM parameters 3.7

5 Figures Figure 1.1: Dimensions of APC-35

50 A confirmation message will be shown on the screen as to whether the password will be disabled. You will have direct access to BIOS setup without

51 Save Changes and Reset [No] Save & reset Save Configuration and reset? [Yes] [No] Discard Changes and Reset Reset Without Saving Reset witho

APC-3X19 User Manual 52 Chapter 4 Installation of Drivers I Important Note: After installing your Windows operating system

APC-3X19 User Manual 53 4.1 Intel Chipset Driver To install the Intel chipset driver, please follow the steps below. Step 1. Access Industrial Pa

APC-3X19 User Manual 54 Step 3. Read the license agreement. Click Yes to accept the terms of the license agreement. Step 4. Click Next to conti

APC-3X19 User Manual 55 Step 5. Click Next. Step 6. Select Yes, I want to restart this computer now. Click Finish then remove any installation

APC-3X19 User Manual 56 4.2 Intel (R) VGA Chipset Driver To install the VGA drivers, follow the steps below to proceed with the installation. Step

APC-3X19 User Manual 57 Step 3. Check Automatically run WinSAT and enable the Windows Aero desktop theme (if supported.) Click Next to continue se

APC-3X19 User Manual 58 Step 5. Click Next. Step 6. Click Next.

APC-3X19 User Manual 59 Step 7. Select Yes, I want to restart this computer now. Click Finish.

6 Chapter 1_____________Getting Started 1.1 Specifications Model No. Specs APC-3519 APC-3719 APC-3919 System Processor Intel G2 socket, suppor

APC-3X19 User Manual 60 4.3 Intel(R) Network Adapter Driver Step 1. Select Intel(R) Network Adapter. Step 2. Click Next to continue.

APC-3X19 User Manual 61 Step 3. Read the license agreement. Select I accept the terms in the license agreement then click Next to continue.

APC-3X19 User Manual 62 Step 5. Click Install to begin the installation. Step 6. Click Finish to compete the installation.

APC-3X19 User Manual 63 4.4 Realtek HD Audio Driver Installation To install the Realtek High Definition (HD) Audio driver, please follow the steps b

APC-3X19 User Manual 64 Step 3. Select Yes, I want to restart my computer now. then click Finish.

APC-3X19 User Manual 65 4.5 Intel(R) USB 3.0 Driver Step 1. Select Intel(R) USB 3.0 Driver Step 2. Click Next to continue.

APC-3X19 User Manual 66 Step 3. Read the license agreement. Click Yes to continue. Step 4. Click Next to continue.

APC-3X19 User Manual 67 Step 5. Click Next to continue. Step 6. Select Yes, I want to restart this computer now. Click Finish.

APC-3X19 User Manual 68 4.6 Intel(R) AMT Driver Step 1. Select Intel(R) AMT Driver Step 2. Click Next to continue.

APC-3X19 User Manual 69 Step 3. Read the license agreement. Click Yes to continue. Step 4. Click Next to continue.

7 Power Consumption Max:51.3W Max:44.2W Max:44.2W Mechanical Structure Black steel front bezel, black steel back cover with aluminum heat-sink IP Rat

APC-3X19 User Manual 70 Step 6. Click Finish to compete the setup.

APC-3X19 User Manual 71 Chapter 5 Touch Screen Installation This chapter describes how to install drivers and other software that wi

APC-3X19 User Manual 72 5.2.1 Installing Software If you have an older version of the PenMount Windows 2000/XP driver installed in your system, plea

APC-3X19 User Manual 73 Step 3. Click Next to continue. Step 4. Read the license Agreement. Click I agree to agree the license agreement.

APC-3X19 User Manual 74 Step 5. Choose the folder in which to install PenMount Windows Universal Driver. Click Install to start the installation.

APC-3X19 User Manual 75 Step 7. Click Continue Anyway to continue. Step 8. Click Finish to compete installation.

APC-3X19 User Manual 76 5.2.2 Software Functions Upon rebooting, the computer automatically finds the new 6000 controller board. The touch screen is

APC-3X19 User Manual 77 Advanced Calibration Advanced Calibration uses 4, 9, 16 or 25 points to effectively calibrate touch panel linearity of age

APC-3X19 User Manual 78 Step 2. Click Standard Calibration to start calibration procedure NOTE: The older the touch screen, the more Advanced M

APC-3X19 User Manual 79 Step 3. Come back to PenMount Control Panel and select Tools then Click Advanced Calibration. Step 4. Select Device to ca

8 Figure 1.2: Dimensions of APC-3719

APC-3X19 User Manual 80 Setting

APC-3X19 User Manual 81 About This panel displays information about the PenMount controller and driver version.

APC-3X19 User Manual 82 Multiple Monitors Multiple Monitors supports two to six touchscreen displays for one system. PenMount drivers for Windows 2

APC-3X19 User Manual 83 Step 2. When the mapping screen message appears, click OK.

APC-3X19 User Manual 84 Step 3. Touch each screen as it displays Please touch this monitor. Press ‘S’ to skip Following this sequence and touching e

APC-3X19 User Manual 85 About You can see how many devices of PenMount controller that are plugged to your system PenMount Monitor Menu Icon The

APC-3X19 User Manual 86 PenMount Monitor has the following function PenMount Rotating Functions The PenMount driver for Windows 2000/XP support

APC-3X19 User Manual 87 NOTE: The Rotate function is disabled if you use Monitor Mapping

9 Figure 1.3: Dimensions of APC-3919